#BOILING UP TO MAKE A PASS MEANING SERIES#

As the temperature of the water increases, the average speed of the water particles also increases. So, what is happening to make these boiling bubbles of water vapor? It's all about temperature and vapor pressure. Where would this air come from? The only option is that the bubbles are made of water vapor. The bubbles are water vapor-they are small pockets of water in the gas phase. It is typically fed to the vacuum distillation unit for further separationįor a specific crude oil grade, the typical volumes and qualities of these distillation cuts are detailed in the crude assay.Are the bubbles made of air? What about some hydrogen and some oxygen? No. Atmospheric bottoms - Contains all of the hydrocarbons that do not vaporize in the atmospheric distillation tower.Atmospheric gasoil - Used to make diesel or converted to gasoline through upgrading in the FCC.Kerosene - Used to make jet fuel or blended into diesel.Heavy naphtha - Mostly upgraded through the reformer but sometimes blended directly into gasoline.Light straight run naphtha - Sold as a feedstock for petrochemicals, blended directly into gasoline or upgraded through isomerization.It is sent to the sat gas plant for further separation Light ends - Stream containing primarily propane and butane.This stream remains a gas and is used as fuel for the refinery Refinery gas - Made up of methane and ethane.Typically, a crude distillation unit will have the following distillation cuts:

The outputs from distillation are distillation cuts. This can be a single crude oil or a mixture of several different crude oil grades.Ī refinery may also re-process a mixture of unfinished or off-spec products (called slops) by blending with fresh crude oil and sending the blend to the distillation unit.

The primary input to an atmospheric distillation unit is crude oil. These are sent to the vacuum distillation for further fractionation under a vacuum.Ĭrude with high salt content will typically be processed through a desalter before going to distillation, to remove salts that could cause corrosion in the distillation tower. The heaviest fractions of the crude do not vaporize and are drawn off at the bottom of the tower as atmospheric bottoms. These individual streams are then sent to other units for further processing or to finished product blending.

These different streams are called distillation cuts or fractions. Hydrocarbons are drawn off of the tower at different heights to get a set of streams of different boiling points. This results in separation of the hydrocarbons based on the different temperatures at which they boil/condense. The lighter (less-dense) hydrocarbons will condense at higher points in the distillation tower, heavier hydrocarbons will condenser lower down. This effect of counter-current flows of rising vapors meeting falling cooler liquids allows equilibrium conditions to be established throughout the column. A portion of this is fed back into the distillation column as a reflux stream to contact with the rising vapors, helping to cool them. A portion of the vapors reaches the top of the column, where it is cooled through heat exchangers and air coolers and partly converted back into liquid. As the vapors cool, their components will condense back into liquid at different levels in the tower based on their boiling point.

#BOILING UP TO MAKE A PASS MEANING SERIES#

As the vapors rise through the tower, they pass through a series of perforated trays or structured packing. The heated crude is injected into the lower part of the distillation column, where much of it vaporizes. The design and operation of the atmospheric distillation tower will limit the type of crude that the refinery can process, further limiting the volume and quality of feed to other process units.Ĭrude oil is first heated to about 700-750F (400C). In most refineries, the bottoms from the atmospheric distillation tower will be sent to the vacuum tower for further separation. Also atmospheric distillation typically provides most of the feed for the other process units in the refinery. All crude oil processed must first go through atmospheric distillation. The primary purpose of the atmospheric distillation tower is to separate crude oil into its components (or distillation cuts, distillation fractions) for further processing by other processing units.Ītmospheric distillation typically sets the capacity limit for the entire refinery. Also known as: atmospheric tower, pipe still, crude unit, primary distillation, crude distillation unit, CDU, fractional distillationĪtmospheric distillation is the first and most fundamental step in the the refining process.

Boiling up to make a pass meaning